netapp_vyos_install [My wiki]

This page is read only. You can view the source, but not change it. Ask your administrator if you think this is wrong.
=====Overview=====
VyOS combines the GNU/Linux operating system and a lot of free networking software under a single, unified management interface. It provides a command line interface in the style of hardware routers, as well as an HTTP API and libraries for configuration scripting.

In this section, we will configure the following topology:

{{:networktopology.jpg?600|}}

=====Download & Install=====
To download the software use the following link:
https://wiki.vyos.net/wiki/Main_Page

And go on "Get the software and download the 64 bit ISO file.
Once you have it downloaded, create a VM using VMWare or VBox or whatever you want to create a Virtual Machine.
In my example I have used a VMWare Player and following these steps:

So first thing first, we need to create a new VM so we choose that option:

{{:vyoscreate.jpg?400|}}

Specify the location of the ISO file which you downloaded from the overview section and press next:
{{:vyosisolocation.jpg?400|}}

Specify the name of the VM and the location for the physical volumes and press next:
{{:vyosnamelocation.jpg?400|}}

Specify the storage and choose whether you want all data into a single file (my example) or you want them in separate file.
{{:vyosstorage.jpg?500|}}

Now, you can uncheck the power on tickbox or you can power it off later, up to you. Here it is left power on by mistake.
{{:vyosaddnetworkinterfaces.jpg?400|}}

=====VM Configure=====
After we have our machine, create and power off, we can see that there is only one network interface:

====Check network Interfaces====
{{:vyoschecknetworkadapters.jpg?400|}}

{{:vyoschecknetworkadaptersv2.jpg?400|}}

====Add network Interfaces====
To add more adapters, press "Add" in the bottom left quorter and choose the type of device you want to add:

{{:vyosaddnetworkadapters.jpg?400|}}

After you press finish you should be able to see two adapters for that virtual machine:

{{:vyosaddnetworkadaptersv2.jpg?400|}}

According our topology, we need 7 interfaces, so repeat that step 5 more times :)
In the end, you should have 7 network interfaces:

{{:vyosnetworkadaptersfinal.jpg?400|}}

====Assign Networks====
Now that we have 7 network adapters, we have to assign them to a specific sub-network or virtualized network. However you wanna tell it :)

You can use the following separation, it is all according the topology above:

{{:vyosnetworkadaptersallocation.jpg?400|}}

In the end, you should have something like that:

{{:vyosnetworkadaptersfinal.jpg?400|}}

====Startup & Login====
After all that, we can finally start and login to the machine:

{{:vyosstartup.jpg?400|}}

The default login credentials are as follows:

Username: vyos

Password: vyos

{{:vyosstartupv2.jpg?400|}}

=====Image & Network Config=====
In this section we will install the network image and configure the networks. So let's get started:

====Image Installation====
To install the image software, just type: "install image" and following the settings. The first set of settings are:

  * Are you sure you want to start: Yes
  * Partitioning: Auto
  * Disk to be used for the installation: "sda", which will be used also as boot disk
  * Verification for deleting all data on sda: Yes

{{:vyosimageinstall.jpg?400|}}

Then we have to fill:

  * The name of the image: default (1.1.8)
  * The Boot file: default (/config/config.boot)
  * Vyos password: blackbox1
  * Booting disk: default (sda)

{{:vyosimageinstallv2.jpg?400|}}

After all is done, we should have the image set up.

{{:vyosimageinstallv3.jpg?400|}}

Now, if we leave it like that, when we restart, it will boot from the disk again and all that will be for nothing. We have to safe that config to the disk:

====Change Booting order====
To change the booting order, we have to shutdown the machine and unmount the disk from the VMWare:
So, first, power off the machine:

{{:vyoschangebooting.jpg?400|}}

Then open the virtual machine in VMWare and unmount the disk as follows.
  - Go to VM Settings
  - CD/DVD(IDE) - Change to: "Use physical device" and untick the "Connect at power on":


{{:vyoschangebootingv2.jpg?400|}}

Now, when the machines boots up, it will boot from the hard disk (/dev/sda) which we configured. Next, configuring the networks :)

====Networks Configuration====
Now, the configure the router, you can either check my other topic, to configure a Cisco router, or you can follow the guide below.
To configure network, use the following:


<Code:bash|Configure the network interfaces>
vyos@vyos:~$configure
[edit]
vyos@vyos:~$set interfaces ethernet eth0 address 172.23.1.254/24
[edit]
vyos@vyos:~$set interfaces ethernet eth1 address 172.23.2.254/24
[edit]
vyos@vyos:~$set interfaces ethernet eth2 address 172.23.3.254/24
[edit]
vyos@vyos:~$set interfaces ethernet eth3 address 172.23.4.254/24
[edit]
vyos@vyos:~$set interfaces ethernet eth4 address 172.23.5.254/24
[edit]
vyos@vyos:~$set interfaces ethernet eth5 address 172.23.7.254/24
[edit]
vyos@vyos:~$set interfaces ethernet eth6 address 172.23.9.254/24
[edit]
</Code>

We have to also allow SSH and SSH using root:

<Code:bash|Enable SSH>
vyos@vyos:~$set service ssh
[edit]
vyos@vyos:~$set service ssh allow-root
[edit]
</Code>

Now that is done, we have to commit our changes:

<Code:bash|Commit changes>
vyos@vyos:~$ commit
vyos@vyos:~$ save
</Code>

Like that, our changes are saved upon restart.


Now, we can finally test it.

====Test====
To test the configuration, be sure that the VMWare virtual interface on your client machine is configured on the same network as the eth0:

{{:vyosclientvmwareadapter.jpg?400|}}


After that, verify you can ping the eth0 IP on the router:

{{:vyosclientpingverify.jpg?500|}}