======Overview====== Apparently in Oracle, you can FORCE the database to open even if it isn't consistent following this procedure: PHASE 1: 1. Apply patch 21307096 then: 2. The fix needs to be enabled with Event 21307096 at level SCN delta. The SCN delta in million units is with the range of values from 1 to 4095 which increases the scn by: lowest_scn + event level * 1000000 Example: if the lowest datafile checkpoint scn in the database is 990396 and the highest is 992660 then SCN delta is 1; given by (992660 - 990396) / 1000000 event="21307096 trace name context forever, level 1" or use this query: select decode(ceil((max(CHECKPOINT_CHANGE#) - min(CHECKPOINT_CHANGE#))/1000000),0,'Event 21307096 is not needed' , 'event="21307096 trace name context forever, level ' ||ceil((max(CHECKPOINT_CHANGE#) - min(CHECKPOINT_CHANGE#))/1000000) ||'"') "EVENT TO SET in init.ora:" from v$datafile_header where status != 'OFFLINE'; Note that the event is needed to activate this fix so please add it in the init.ora file. PHASE 2: 1) Backup the database while the database is closed. THE INSTRUCTIONS HERE ARE DESTRUCTIVE. YOU ARE STRONGLY ADVISED TO BACKUP THE DATABASE BEFORE PROCEEDING. IF YOU DO NOT DO THIS YOU MAY LOSE THE CHANCE TO TRY OTHER OPTIONS. 2) Disable this database from EM if running. We also need to disable RAC to avoid Auto restart. 3) If your datafiles are from different points in time, it is best to try to use system tablespace datafiles at a similar timestamp to the OLDEST files you have online in the database. This reduces the chance that you will get problems during the bootstrap phase of opening the database. 4) Edit your init.ora file to change undo_management and add two parameters. * Change UNDO_MANAGEMENT=AUTO to UNDO_MANAGEMENT=MANUAL * Remove or comment out UNDO_TABLESPACE and UNDO_RETENTION. * Add CLUSTER_DATABASE=FALSE JOB_QUEUE_PROCESSES=0 _ALLOW_RESETLOGS_CORRUPTION = TRUE * If you only have a spfile available, you can from the closed, nomount or the mount stage create an init.ora file as follows: SQL> CREATE PFILE FROM SPFILE; Do NOT edit the SPFILE. 5) Invoke SQL*Plus, startup mount, check that correct init.ora was used and all datafiles are in the status of online or system. $ sqlplus "/as sysdba" SQL> startup mount pfile = (full path / file name ato init.ora) Confirm that the hidden parameters from step 3 were used: SQL> show parameters corrupt You should see both hidden parameters listed. If not, the wrong init.ora may have been modified. Do not continue until "show parameters corrupt" shows both hidden parameters. SQL> show parameters undo You should see undo management set to manual. If not, the wrong init.ora may have been modified. Do not continue until "show parameters undo" shows undo management as manual. Check that all files you want to open with are listed as ONLINE or as SYSTEM. SQL> select name, file#, status from v$datafile where status not in ('SYSTEM', 'ONLINE'); If any rows are returned from the query above, bring the file(s) online with: SQL> ALTER DATABASE DATAFILE file# ONLINE; and repeat until there are no files in an OFFLINE status. If any file remains or changes into "recover" status after you try to online the file proceed to step 6. 6) Perform a fake incomplete recovery then open the database with resetlogs. SQL> recover database using backup controlfile until cancel; WHEN PROMPTED FOR AN ARCHIVELOG FILE TYPE cancel THEN PRESS ENTER. SQL> ALTER DATABASE OPEN RESETLOGS; 7) If the database opens try selecting from a table. For example: SQL> SELECT SYSDATE FROM DUAL; If you get a row back the database is open and "functional". If you wish, you may try to select from a other tables to make sure the database is functional enough for the required export. With the database open and functional you should attempt to export the database IMMEDIATELY. Since database is unstable, don't try another shutdown/startup unless needed. Once you have an export the database MUST be recreated from scratch. This means dropping and deleting ALL datafiles and creating a new database from scratch. A database which has been opened in this way but not rebuilt will not be supported by Oracle. Any delay in exporting the contents or any attempt to use the system may cause irreparable damage. NOTE: BE SURE TO REVERSE / REMOVE THE INIT.ORA PARAMETERS ADDED IN STEP 3 OTHERWISE YOU MAY ACCIDENTALLY CORRUPT ANY NEW DATABASE CREATED USING THE SAME INIT.ORA FILE. 8) If the instance crashed in the open phase of step 5, check for trace files in the background dump destination. If you find a trace file, check to see if the trace file has an ORA-00600 [2662] or ORA-00600 [4000] error in it. Either of these errors may also be seen in the alert.log file. If you see the ORA-00600 [2662] or ORA-00600 [4000] error, provide Oracle Support Services the full error message. Oracle Support Services will provide steps to advance the SCN using a hidden parameter. NOTE: BE SURE TO REVERSE / REMOVE THE INIT.ORA PARAMETERS ADDED IN STEP 3 OTHERWISE YOU MAY ACCIDENTALLY CORRUPT ANY NEW DATABASE CREATED USING THE SAME INIT.ORA FILE. ************************************************************************* * * * CAUTION: Once the database is open, it is imperative that you export, * * rebuild the database, and import. * * * * By forcing open the database in this fashion, there is a strong * * likelihood of logical corruption, possibly affecting the data * * dictionary. Oracle does not guarantee that all of the data will be * * accessible nor will it support a database that has been opened by * * this method and that the database users will be allowed to continue * * work. All this does is provide a way to get at the contents of the * * database for extraction, usually by export. It is up to you to * * determine the amount of lost data and to correct any logical * * corruption issues. * * * *************************************************************************